Changelog - Medeek Truss Plugin

This Changelog is a list of all of the signficant updates and modifications that have occurred with the Medeek Truss Plugin since its inception in October of 2015. The most current versions/revisions are listed at the top.

Download previous versions of the plugin here.

Version 3.6.3 - 07.26.2024

Added a duplicate roof assembly check to the regen module for rafter, complex and truss roofs.

Version 3.6.2 - 07.21.2024

Enabled "flat" ceiling gypsum for complex rafter roofs.
Fixed a minor bug with the hip-and-ridge for hip rafter roofs.

Version 3.6.1 - 07.19.2024

Added Soffit Cut within Advanced Options for Complex Rafter Roofs.
Fixed a critical bug with the complex roof module.

Version 3.6.0 - 07.18.2024

Added rake parameters to the dutch gable rafter roof edit menu.
Fixed a bug with the hip and dutch gable advanced options module (when sheathing is disabled).

Version 3.5.9 - 07.17.2024

Added a "Rafter Roof" tab to the Global Settings.
Added Sub-Fascia parameters to the Rafter Roof and Complex Roof tabs of the Global Settings.

Version 3.5.8 - 07.12.2024

Enabled the "Edit Roof Assembly" function for gable rafter roofs with glulam beams (imperial and metric units).
Enabled the "Edit Roof Assembly" function for I-joist rafter roofs with glulam beams (imperial and metric units).
Enabled the "Edit Roof Assembly" function for I-joist rafter roofs with dual glulam beams (imperial and metric units).
Added BCI, LPI, Red-I and PKI I-joists to the rafter roof module (glulam beam and dual glulam beam roofs).

Version 3.5.7 - 07.05.2024

Fixed a bug for all rafter roofs that have glulam beams.

Version 3.5.6 - 07.03.2024

Enabled a graphical user interface for Rafter Roof selection.
Enabled a graphical user interface for Floor selection.
Fixed a bug introduced in Version 3.5.3 for all I-joist, lumber and truss floors (when adv. floor options disabled).

Version 3.5.5 - 06.22.2024

Fixed a bug introduced in Version 3.4.7 for all rafter and truss roofs (when adv. roof options disabled).

Version 3.5.4 - 06.15.2024

Fixed a bug introduced in Version 3.4.7 for all rafter and truss roofs.

Version 3.5.3 - 06.09.2024

Enabled a feature to selectively remove specific trusses from floor truss assemblies.
Enabled a feature to selectively remove specific joists from I-joist and lumber floor assemblies.

Version 3.5.2 - 05.30.2024

Enabled ceiling insulation for floor trusses: Batt, Blown-in.
Enabled ceiling insulation for I-Joist and Lumber floors: Batt, Blown-in.
Fixed a bug with ceiling gypsum for inset floors (I-joist and Lumber).
Fixed a minor bug with joist hangers for common lumber sizes for inset floors.

Version 3.5.1 - 05.28.2024

Enabled ceiling insulation for gambrel attic and attic trusses: Batt, Blown-in.
Enabled ceiling insulation for scissor trusses: Batt, Blown-in.

Version 3.5.0 - 05.26.2024

Enabled "flat" ceiling gypsum for dutch gable rafter roofs.
Enabled "flat" ceiling gypsum for hip rafter roofs.
Fixed a bug with the global settings for rafter and truss roofs when the layer/tags option is turned off.

Version 3.4.9 - 05.26.2024

Enabled "vaulted" ceiling insulation for gable rafter roofs (symmetric and asymmetric): Batt, Blown-in.
Added "vaulted" ceiling gypsum to gable rafter roofs.
Enabled "flat" ceiling gypsum for gable rafter roofs with ceiling joists option enabled.

Version 3.4.8 - 05.25.2024

Enabled Roof Connections for the following additional truss types: tray, monocathedral, cambered, monoscissor and coffer.
Enabled the "Edit Roof Assembly" function for dutch gable rafter roofs (imperial and metric units).
Enabled the following 3D roof cladding material for dutch gable rafter roofs: Metal.

Version 3.4.7 - 05.23.2024

Enabled Roof Connections between complex roofs, rafter roofs, truss roofs and solid groups.
Added the "Configure Roof Connection" feature to the edit menu for complex, rafter and truss roofs.

Version 3.4.6 - 05.16.2024

Enabled sheathing, cladding, ridge cap and labels for dual pitch trusses.
Updated the polynesian truss so layers and materials are properly assigned.
Enabled the "Edit Truss Assembly" function for dual pitch trusses (imperial and metric units).
Enabled the "Edit Truss Assembly" function for polynesian trusses (imperial and metric units).
Enabled the "Edit Truss Assembly" function for bowstring trusses (imperial and metric units).
Enabled the "Edit Truss Assembly" function for bow barrel trusses (imperial and metric units).

Version 3.4.5 - 05.10.2024

Enabled ceiling insulation for shed rafter roofs: Batt, Blown-in.
Enabled ceiling insulation for gable rafter roofs: Batt, Blown-in.
Enabled ceiling insulation for hip rafter roofs: Batt, Blown-in.
Enabled the "Edit Truss Assembly" function for all flat trusses (imperial and metric units).

Version 3.4.4 - 05.02.2024

Added ceiling gypsum for cambered and mono cathedral trusses.
Enabled the "Edit Truss Assembly" function for cambered and mono cathedral trusses (imperial and metric units).
Enabled labels for cambered and mono cathedral trusses.
Fixed some minor bugs for mono cathedral trusses.

Version 3.4.3 - 04.30.2024

Added ceiling gypsum for tray and coffer trusses.
Enabled the "Edit Truss Assembly" function for tray and coffer trusses (imperial and metric units).
Enabled labels for tray and coffer trusses.
Updated the license verification system with a more secure and improved algorithm.

Version 3.4.2 - 04.23.2024

Fixed a compatibility bug with SketchUp 2024 (Fixnum & Bignum) while maintaining backward compatibility with previous versions of SketchUp.

Version 3.4.1 - 04.18.2024

Fixed a compatibility bug with SketchUp 2024 while maintaining compatibility with previous versions of SketchUp.

Version 3.4.0 - 01.11.2024

Added a "Primitive" option to the roof framing parameter within the Draw and Edit menus for the following rafter roofs: Gable, Shed, Shed (with ledger), Hip.
Added lower pitches to the draw menus for the following rafter roofs: Gable, Shed, Shed (with ledger), Hip.

Version 3.3.9 - 12.30.2023

Updated and improved the license verification module.
Disabled redundant logging to improve plugin performance.

Version 3.3.8 - 12.02.2023

Updated the face selection algorithm of the complex roof draw tool.

Version 3.3.7 - 10.29.2023

Enabled the "Edit Truss Assembly" function for symmetric cathedral trusses (imperial and metric units).
Added ceiling gypsum for symmetric cathedral trusses.
Fixed a minor bug with parellel chord trusses.

Version 3.3.6 - 10.20.2023

Sheathing Vertical Offset parameters added for attic trusses.
Cladding Vertical Offset parameters added attic trusses.
Wall Cladding Gap parameter added for common, monopitch and attic trusses.

Version 3.3.5 - 10.06.2023

Sheathing Vertical Offset parameters added for common and monopitch trusses.
Cladding Vertical Offset parameters added for common and monopitch trusses.

Version 3.3.4 - 10.01.2023 thru 10.02.2023

Added a "Complex Roof" tab to the Global Settings.
Added a "Roof Framing" and "Advanced Options" parameter to the Complex Roof tab of the Global Settings.
Added a "Primitive" option to the roof framing parameter within the Draw and Edit menus for complex roofs.
Enabled the Up Arrow key as a method to toggle between "face" or "polygon" mode within the complex roof draw tool.
Added a "Draw Mode" parameter to the Complex Roof tab of the Global Settings.
Enabled a vertex (roof plane) selection method within the face selection algorithm of the Draw tool for complex roofs.

Version 3.3.3 - 09.22.2023

Improved the responsiveness of the "Edit Roof Plane" tool and the "Move Roof Edge" tool for complex roofs.

Version 3.3.2 - 09.17.2023

Added statistics for complex roofs (Medeek Estimator integration).

Version 3.3.1 - 09.03.2023 thru 09.09.2023

Added a hip, valley and flying hip rafters to the complex roof framing module.
Refined the framing algorithm for hip, valley and flying hip rafters.
Minor bug fix within the rafter framing module for complex roofs.
Version 3.3.1d - 09.09.2023
- Fixed a bug within the global settings for complex roofs.
- Updated the straight skeleton algorithm to better remove redundant edges within roof planes/faces.
- Improved the robustness of the complex roof module (framing and cladding) for specific cases.

Version 3.3.0 - 08.31.2023

Added a rafter offset parameter for complex roof framing.
Fixed a minor bug with complex roof framing for half hip roofs set to custom pitches.

Version 3.2.9 - 08.28.2023 thru 08.30.2023

Fixed a critical bug with the truss removal feature for truss sets.
Fixed a critical bug with the hip rafter roof module.
Fixed the non-orthogonal rafter framing bug for complex roofs.

Version 3.2.8 - 07.05.2023

Enabled a ridge centering option for asymmetric gable rafter roofs.
Enabled a ridge centering option for asymmetric hip rafter roofs.

Version 3.2.7 - 06.26.2023 thru 06.28.2023

Fixed a bug with the truss removal feature.
Enabled a feature to selectively remove specific trusses from common and monopitch truss assemblies.
Fixed a minor bug with the truss removal feature for all truss types.

Version 3.2.6 - 06.22.2023

Enabled the "Edit Truss Assembly" function for all gambrel attic trusses.
Enabled a gable wall cut for gambrel attic trusses.
Enabled a feature to selectively remove specific trusses from gambrel attic truss assemblies.

Version 3.2.5 - 06.17.2023

Enabled a gable wall cut for attic trusses.
Enabled a feature to selectively remove specific trusses from attic truss assemblies.

Version 3.2.4 - 02.09.2023

Enabled subtractive geometry for all complex rafter roofs.
Updated the subtract feature to include gutter downspouts for all rafter roofs.

Version 3.2.3 - 02.06.2023

Fixed an infinite loop bug for (full) roof returns on truss roofs.
Updated the subtract feature to include roof return rafters and gutter downspouts for truss roofs.

Version 3.2.2 - 01.11.2023

Enabled layer control integration with the Medeek Project extension.
Moved the Medeek Tools module to the Medeek Project extension.

Version 3.2.1 - 01.04.2023

Updated and adjusted the logging function and auto-update functions.

Version 3.2.0 - 11.28.2022

Fixed a minor bug with the roof cladding thickness parameter when the materials option is toggled off.

Version 3.1.9 - 11.25.2022

Enabled subtractive geometry for all shed rafter roofs.

Version 3.1.8 - 08.29.2022

Added a parameter into the general tab of the global settings to allow for adjustment of the size of labels and annotations.
Added a parameter into the general tab of the global settings to allow for adjustment of the font for text found within annotations and labels.
Added a "resolution" parameter into the general tab of the global settings for adjusting the smoothness of annotation text.
Added a "Label Rotation" parameter (0 or 180 degrees).
Enabled various annotation options/parameters for truss roofs.

Version 3.1.7 - 08.26.2022

Enabled the following 3D roof cladding material for shed rafter roofs: Metal.

Version 3.1.6 - 06.05.2022

Enabled ceiling insulation for common trusses: Batt, Blown-in.
Enabled ceiling insulation for monopitch trusses: Batt, Blown-in.
Added an insulation layer in the global settings.

Version 3.1.5 - 05.07.2022

Enabled 3D roof and wall cladding materials for attic trusses.

Version 3.1.4 - 04.27.2022

Fixed a minor bug with the advanced options for scissor trusses.
Updated the scissor truss module so that raised heel trusses are properly rendered/drawn.

Version 3.1.3 - 04.10.2022

Enabled 3D roof and wall cladding materials for monopitch trusses.
Fixed a bug with the valley set detection option.

Version 3.1.2 - 02.15.2022

Enabled MPC wood blocking panels for common trusses.

Version 3.1.1 - 02.13.2022

Enabled advanced options for mono scissor trusses.
Enabled the "Edit Truss Assembly" function for all mono scissor trusses (imperial and metric units).

Version 3.1.0 - 02.10.2022

Enabled customizable colors for system materials for complex roofs: Outline and Geometry.

Version 3.0.9 - 02.09.2022

Enabled soffit and fascia for hip truss sets.
Fixed a minor bug with the hip truss set module.
Removed the Gutter Extension parameter from the hip truss set edit menu.

Version 3.0.8 - 01.29.2022

Added ceiling gypsum and ceiling battens to all floor assemblies.

Version 3.0.7 - 01.25.2022

Added energy/raised heels for 4/2 scissor trusses (1 variant: vertical w/ strut).

Version 3.0.6 - 11.30.2021

Added ceiling gypsum to shed and shed w/ ledger rafter roofs.
Enabled ceiling gypsum for all shed rafter roofs with ceiling joists enabled.

Version 3.0.5 - 11.03.2021

Added additional energy/raised heels for double fink truss (2 variants: wedge and slider).

Version 3.0.4 - 10.23.2021

Added error checking code into various HTML menus for roof and wall materials.

Version 3.0.3 - 10.02.2021

Added custom materials to the roof and wall cladding parameters of the Sheathing tab within the Global Settings.

Version 3.0.2 - 08.23.2021

Fixed a bug with ceiling joists for shed rafter roofs.
Fixed a bug with rafter roofs with glulam beams that have soffit and fascia enabled.
Updated the wireframe preview of the draw tool for select rafter and truss roof types.

Version 3.0.1 - 08.08.2021

Fixed a bug with the edit menu for common trusses and custom materials.

Version 3.0.0 - 08.03.2021

Fixed a minor bug with the rafter framing module for complex roofs.
Adjusted the tool tips within the HTML edit menu for common trusses.

Version 2.9.9 - 07.25.2021

Enabled the rafter framing module for complex roofs.

Version 2.9.8 - 07.21.2021

Improved the organization of the advanced options within the edit menu for complex rafter roofs.
Enabled the following 3D roof cladding material for complex rafter roofs: Metal.
Added a horizontal offset parameter for the 3D metal roof cladding material for complex rafter roofs.
Added the option for adjusting the angle or pitch within the edit menu for complex rafter roofs.
Added a "Valley Set Check" option for common truss roofs (roof cladding trim only).

Version 2.9.7 - 07.18.2021

Improved the organization of the advanced options within the edit menu for valley and hip truss sets.
Enabled the following 3D roof cladding material for valley and hip truss sets: Metal.
Added a horizontal offset parameter for the 3D metal roof cladding material for valley and hip truss sets.
Added the option for adjusting the angle or pitch within the edit menu for valley and hip truss sets.

Version 2.9.6 - 07.17.2021

Improved the organization of the advanced options within the edit menu for hip rafter roofs.
Enabled the following 3D roof cladding material for hip rafter roofs: Metal.
Added a horizontal offset parameter for the 3D metal roof cladding material for hip rafter roofs.
Added the option for adjusting the angle or pitch within the edit menu for hip rafter roofs.

Version 2.9.5 - 07.16.2021

Improved the organization of the advanced options within the edit menu for gable rafter roofs.
Enabled the following 3D roof cladding material for gable rafter roofs: Metal.
Added a horizontal offset parameter for the 3D metal roof cladding material for gable rafter roofs.
Added the option for adjusting the angle or pitch within the edit menu for gable rafter roofs.

Version 2.9.4 - 07.14.2021

Improved the organization of the advanced options within the edit menu for common trusses.
Enabled the following 3D roof cladding material for common trusses: Metal.
Added a horizontal offset parameter for the 3D metal roof cladding material for common trusses.

Version 2.9.3 - 07.13.2021

Added the option for adjusting the angle or pitch within the edit menu for common trusses.
Added tooltips for advanced options within the edit menu for common trusses.
Enabled the following 3D wall cladding materials for gable walls of common trusses: Board and Batten, Metal, Lap, Shiplap, and Log.
Added both horizontal and vertical offset parameters for wall cladding materials for common trusses.

Version 2.9.2 - 07.10.2021

Enabled subscription and permanent licensing.
The License tab of the Global Settings now displays the license type.

Version 2.9.1 - 07.08.2021

Added a "Regen" context menu item for valley truss sets.
Enabled subtractive and custom geometry for valley truss set assemblies.
Enabled HTML draw and edit menus for valley truss sets.
Labels and callouts added to valley truss sets.
Enabled the ridge cap option for valley truss sets.

Version 2.9.0 - 07.02.2021

Added a "Regen" context menu item for hip truss sets.
Enabled subtractive and custom geometry for hip truss set assemblies.
Enabled the edit function for hip truss sets.
Labels and callouts added to hip truss sets.
Added an "inset" parameter for hurricane ties into the global settings.

Version 2.8.9 - 06.26.2021

Added a "Regen" context menu item for floor truss assemblies.
Enabled subtractive and custom geometry for floor truss assemblies.
Enabled the edit function for floor truss assemblies.

Version 2.8.8 - 06.24.2021

Added a "Regen" context menu item for all I-joist and lumber floor assemblies.
Enabled subtractive geometry for I-joist and lumber floors.
Enabled the "Edit Floor Assembly" function for lumber floors.

Version 2.8.7 - 06.23.2021

Added stats (roof cladding, sheathing, drip edge, hip & ridge, rafters) for gable and hip rafter roofs which can be analyzed within the Medeek Estimator (Wall Extension) module.

Version 2.8.6 - 06.18.2021

Added a "Regen" context menu item for all rafter roof assemblies (eg. Gable, Hip, Shed etc...)
Streamlined and improved the organization and naming convention of hip and gable rafter roofs.
Enabled subtractive geometry for hip and gable rafter roofs.

Version 2.8.5 - 06.14.2021

Added stats (roof cladding) for common and monopitch truss roofs which can be analyzed within the Medeek Estimator (Wall Extension) module.
Enabled net area calculations for roof sheathing and roof cladding statistics.

Version 2.8.4 - 06.13.2021

Added a "Regen" context menu item for all truss assemblies (eg. Common Trusses, Scissor Trusses, Timber Trusses etc...)
Added an option for subtractive geometry into the General tab of the Global Settings.
Sub-groups within truss assemblies can be made persistent and "subtractive" by naming these groups to (subtract1, subtract2, subtract3, etc...)
Components within truss assemblies can also be made persistent and "subtractive" by naming the component instance to (subtract1, subtract2, subtract3, etc...)
Subtractive geometry can be constrained to only subtract from Sheathing and Cladding by setting the subtractive geometry parameter to "SHEATHING" in the global settings.

Version 2.8.3 - 06.04.2021

Added four additional parameters to the "User Interface" section of the General tab of the global settings. This allows the customization (colors) of the HTML menus and buttons.

Version 2.8.2 - 03.24.2021

Added additional pitches to the shed and shed w/ ledger draw menus.

Version 2.8.1 - 03.13.2021

Standardized the naming convention of the plugin toolbars.

Version 2.8.0 - 02.10.2021

Minor modification to the range of available pitches for valley truss sets.

Version 2.7.9 - 10.23.2020

Fixed a "rounding error" bug for pyramid shaped hip rafter roofs.

Version 2.7.8 - 10.09.2020

Added a "Refresh Licensee Data" button within the License tab of the Global Settings.

Version 2.7.7 - 07.31.2020

Fixed a bug with all assemblies when auto-assigment of materials is turned off in the global settings.

Version 2.7.6 - 05.11.2020

Added the Skylights toolbar.
Enabled skylights for all truss, rafter and complex roofs.
Enabled skylights for generic roofs.

Version 2.7.5 - 05.05.2020

Enabled a toggle feature (Ctrl key) for the Trim tool so that the selection can be retained or removed.

Version 2.7.4 - 05.02.2020

Fixed a bug with the soffit and fascia module for all truss types.

Version 2.7.3 - 04.26.2020

Added a Global Reset button in the General tab of the Global Settings.

Version 2.7.2 - 04.24.2020

Added wall sheathing thickness and wall cladding thickness parameters to the advanced options for trusses.
Enabled advanced options for tail bearing trusses.
Enabled the "Edit Truss Assembly" function for all tail bearing trusses (imperial and metric units).
Labels and callouts added to tail bearing trusses.

Version 2.7.1 - 04.13.2020

Enabled the "Edit Roof Assembly" function for shed w/ ledger rafter roofs (imperial and metric units).
Enabled soffit and fascia for shed w/ ledger rafter roofs: boxed, gable, angled.
Enabled a roof cladding extension parameter for shed w/ ledger rafter roofs.
Added the option in the shed w/ ledger rafter roof edit menu to specify a separate front and back overhang length.
Enabled a "No Framing" mode for shed w/ ledger rafter roofs.

Version 2.7.0 - 04.12.2020

Enabled the "Edit Truss Assembly" function for all timber trusses (imperial and metric units).

Version 2.6.9 - 04.11.2020

Enabled the "Edit Truss Assembly" function for all parallel chord trusses (imperial and metric units).
Labels and callouts added to parallel chord trusses.

Version 2.6.8 - 04.10.2020

Fixed a show_modal bug for macOS in the Timber Truss HTML menu dialog.

Version 2.6.7 - 02.09.2020

Fixed a bug in the text input method of the draw menu for complex rafter roofs.
Added a T1-11 built-in material into the material library.

Version 2.6.6 - 01.29.2020

Fixed a bug in the (complex roofs) roof plane edit menu for the outlooker size parameter.
Fixed a bug involving truss assemblies and valley set assemblies that are created in the same SketchUp session.

Version 2.6.5 - 12.18.2019

Enabled an "orthogonal mode" for the complex roof draw menu.
Added the ability to delete points in the complex roof draw menu.

Version 2.6.4 - 12.16.2019

Exposed the roof soffit layer name in Layers tab of the global settings.
Fixed multiple bugs in the gambrel attic truss module.

Version 2.6.3 - 12.02.2019

Fixed multiple bugs in the complex roof module as related to metric templates.

Version 2.6.2 - 11.17.2019

Allowed the option for interior half hips within complex roofs.

Version 2.6.1 - 11.07.2019

Added ridge boards for complex roofs.

Version 2.6.0 - 10.30.2019

Added the terminal roof plane option for complex roofs.
Added the "Complex Roof Connection" tool to the complex roof toolbar.
Enabled Roof Connections for complex roofs: roof assemblies or solid groups.
Added the "Remove Roof Connection" feature to the edit menu for complex roofs.

Version 2.5.9 - 10.26.2019

Added a trim fascia rake parameter for complex roofs.
Resolved the issue with the soffit for the "gable" soffit configuration for complex roofs.

Version 2.5.8 - 10.24.2019

Added soffit & fascia for complex roofs.

Version 2.5.7 - 10.14.2019

Allowed the option for interior gables within complex roofs.
Fixed a bug in the gutter module for complex roofs.

Version 2.5.6 - 10.11.2019

Added gutters for complex roofs.

Version 2.5.5 - 10.10.2019

Added sub-fascia and rakeboards for complex roofs.

Version 2.5.4 - 10.08.2019 thru 10.09.2019

Added cladding for complex roofs.
Added labels for complex roofs.
Fixed a bug with non-orthogonal roof plane labels for complex roofs.
Resolved some minor bugs and stability issues with half hip and dutch gable roof options with complex roofs.

Version 2.5.3 - 10.05.2019

Added sheathing for complex roofs.
Fixed the sheathing at the gable overhang for dutch gable complex roofs.

Version 2.5.2 - 10.04.2019

Added the half hip option for complex roofs within the "Edit Roof Plane" tool/menu.
Added the dutch gable option for complex roofs within the "Edit Roof Plane" tool/menu.
The "Edit Roof Plane" tool has been made non-persistent to further improve stability.

Version 2.5.1 - 10.02.2019 thru 10.03.2019

Enabled the "Edit Roof Plane" tool, allowing for customized roof planes within complex roof assemblies.
Added the gable end option for complex roofs within the "Edit Roof Plane" tool/menu.
Added logic so that customized roof planes can co-exist with the "Move Roof Edge" and "Edit Roof Outline" tools of the complex roof module.

Version 2.5.0 - 09.28.2019

Fixed a critical performance bug that affects all the modules within the extension.
Added the Complex Roofs toolbar.

Version 2.4.9 - 08.27.2019

Fixed the trim tool so that it now able to trim hollow sections (ie. pipes, rectangular tubes).

Version 2.4.8 - 06.16.2019 thru 06.20.2019

Added a Soffit/Fascia tab to the Global Settings.
Corrected the code for raising and logging exceptions.
Language files moved to .rbs format.

Version 2.4.7 - 06.13.2019 thru 06.14.2019

Enabled a "No Framing" mode for gable, hip and shed rafter roofs. This feature is also available for asymmetric gable and hip roofs.
Added the complex roof icon to the main toolbar.
Addressed a number of critical bug fixes for metric templates.

Version 2.4.6 - 06.08.2019

Enabled gable and angled soffit & fascia for common, attic, scissor, and cathedral trusses.
Enabled gable and angled soffit & fascia for monopitch trusses.
Added the ability to import materials directly from the model within the Custom Material Libary/Manager in the global settings.

Version 2.4.5 - 06.07.2019

Fixed a minor bug with the shed rafter roof module.
Enabled gable and angled soffit & fascia for all gable rafter roofs.

Version 2.4.4 - 06.05.2019 thru 06.06.2019

Enabled soffit and fascia for shed rafter roofs.
Enabled a roof cladding extension parameter for shed rafter roofs.
Enabled the "Edit Roof Assembly" function for shed rafter roofs (imperial and metric units).
Added the option in the shed rafter roof edit menu to specify a separate front and back overhang length.
Shed roofs auto-trim upper rafter tails as required when soffit is specified.
Enabled gable and angled soffit & fascia for shed rafter roofs.

Version 2.4.3 - 06.02.2019 thru 06.03.2019

Enabled soffit and fascia for the following truss types: common, attic, scissor, monopitch, cathedral.
Enabled a roof cladding extension parameter for truss roofs.
Enabled the "Edit Truss Assembly" function for all cathedral trusses (imperial and metric units).
Added the floor sheathing option to the attic truss edit menu.
Parameter change highlighting enabled for truss roof edit menus.
Roof returns (full and hip) enabled for monopitch trusses.
Addressed some minor bugs with the truss gutter module.
Soffit and Fascia added to truss roofs with full or hip returns.
Labels and callouts added to attic, scissor, and cathedral trusses.
Added the soffit box extension parameter for truss roofs.
The Medeek Truss extension will no longer officially support SketchUp 2015 and SketchUp 2016, only SketchUp 2017 and newer will be supported.

Version 2.4.2 - 05.27.2019

Enabled soffit and fascia for gable rafter roofs.
Enabled a roof cladding extension parameter for gable rafter roofs.
Enabled custom materials for roof sheathing and roof cladding in the HTML edit menu for gable rafter roofs.
Added the soffit box extension parameter for gable rafter roofs.

Version 2.4.1 - 05.25.2019

Parameter hightlight (input) color added to General tab of global settings.
Parameter change highlighting enabled for the gable and hip rafter roof edit menus.
Added the indexing parameter for roofs and floors to the General tab of the global settings.

Version 2.4.0 - 05.19.2019

Enabled soffit and fascia for all hip rafter roofs.
Fixed a minor bug with the ridge cap extension for asymmetric hip roofs.
Enabled custom materials for roof sheathing and roof cladding in the HTML edit menu for all hip rafter roofs.

Version 2.3.9 - 05.17.2019

Enabled a roof cladding extension parameter for all hip rafter roofs.

Version 2.3.8 - 05.16.2019

Fixed a bug with the pitch and area callouts for asymmetric gable rafter roofs.
Fixed a bug with the back/rear outlooker length for gable rafter roofs which now allows for a building or roof length that is a non-integer multiple of the rafter spacing.
Added the option in the gable rafter roof edit menu to specify a separate front and back overhang length.

Version 2.3.7 - 05.13.2019

Enabled asymmetric hip rafter roofs (imperial and metric units).

Version 2.3.6 - 05.01.2019

Enabled asymmetric gable rafter roofs (imperial and metric units).

Version 2.3.5 - 04.28.2019

Fixed the show_modal bug for macOS in the Materials tab of the global settings.

Version 2.3.4 - 04.24.2019

Enabled the "Edit Roof Assembly" function for gable and hip rafter roofs (imperial and metric units).
Corrected an issue with H2.5A hurricane ties when utilized with raised heel trusses.

Version 2.3.3 - 04.17.2019

Enabled the "Edit Truss Assembly" function for attic trusses (imperial units only).
Improved formatting of all HTML edit menus: Common, Monopitch, Scissor, Attic.

Version 2.3.2 - 04.15.2019

Enabled the "Edit Truss Assembly" function for all scissor trusses (imperial and metric units).

Version 2.3.1 - 03.15.2019

Fixed a bug with the wall cladding material parameter in the global settings.
Updated toolbar icons to be compatible with 4k (UHD) resolution monitors.

Version 2.3.0 - 03.01.2019

Fixed one bug and a number of minor issues with monopitch trusses.
Enabled sheathing and cladding at the heel of raised heel common and monopitch trusses.
Added metal plates for raised heel monopitch trusses: wedge, slider, vertical w/ strut.

Version 2.2.9 - 02.25.2019

Fixed a bug in the display of the toolbars (Mac and Windows).
Enabled custom materials for wall sheathing, wall cladding, roof sheathing and roof cladding in the HTML advanced options draw menu for attic trusses. This update also resolved an associated bug in the global settings for attic trusses.

Version 2.2.8 - 01.06.2019 thru 01.18.2019

License expiration date now appears in the License tab of the Global Settings when plugin is registered.
Fixed a bug in the license and registration module.

Version 2.2.7 - 12.27.2018 thru 01.04.2019

Roof and Floor labels option added to the General tab of the Global Settings.
Roof and Floor label prefixes can be customized in the General tab of the Global Settings.
Roof labels enabled for common trusses.
When framing callouts are enabled the area of each roof plane will be shown below the roof label (currently only common truss assemblies have this feature available).
Added a customizable color for roof and floor labels within the Material tab of the Global Settings.
Added additional layers for dimensions, annotations, 2d geometry, building code and engineering.
Enabled roof labels and framing callouts for monopitch truss assemblies.
Added stats (roof sheathing) for common and monopitch truss roofs which can be analyzed within the Medeek Estimator (Wall Extension) module.
Enabled roof labels and framing callouts for all rafter roof assemblies: Gable, Hip, Dutch Gable, TJI, TJI w/ Glulam, Shed etc...
All roof framing callouts now include the roof pitch or angle in degrees (metric templates).
Added additional stats: (ridge cap, drip edge) for common and (drip edge) for monopitch truss roofs which can be analyzed within the Medeek Estimator (Wall Extension) module.

Version 2.2.6 - 12.16.2018 thru 12.18.2018

Added the Miter Cut icon to the Medeek Tools toolbar.
Added the Miter Cut function for (solid) groups and components.
Enabled temporary (construction) dimensions for trusses, roofs and floor assemblies.
Added a section in the General tab of the global settings for configuring construction dimensions.
Added the Split icon to the Medeek Tools toolbar.
Added the Split function for (solid) groups and components: split plane via one face or three points.
Addressed a bug in the Split function regarding nested groups and components.

Version 2.2.5 - 12.08.2018 thru 12.13.2018

Added the Trim 2 icon to the Medeek Tools toolbar.
Added the Trim 2 function for (solid) groups and components. This trim function allows the user to select two trimming planes.
Added the Extend function for (solid) groups and components. This function allows the user to extend a member to a single plane/face.
Added the Trim 3 icon to the Medeek Tools toolbar.
Added the Trim 3 function for (solid) groups and components. This trim function allows the user to select three trimming planes.
Enabled the ability to invert your selection within the Trim 2 and Trim 3 tools using the "CTRL" key in Windows.

Version 2.2.4 - 11.02.2018 thru 11.08.2018

Enabled wall sheathing, wall cladding and roof cladding for monopitch trusses.
Enabled gutters and downspouts for monopitch trusses.
Enabled the "Edit Truss Assembly" function for all monopitch trusses (imperial and metric units).
Licensee name now appears in the License tab of the Global Settings when plugin is registered.
Removed all advertising banners from the global settings.

Version 2.2.3 - 10.26.2018

Added a Custom Material Library/Manager in the Materials tab of the Global Settings.
Enabled custom materials for wall sheathing, wall cladding, roof sheathing and roof cladding in the HTML advanced options draw and edit menus for common trusses.
Enabled the ability group materials and control which drop down menu they will appear in.
Added an SKM file import utility to the Material Library.
Default wall sheathing and wall cladding materials brought in line with options available in wall plugin.
Fixed a bug in the attribute library for common trusses.

Version 2.2.2 - 10.14.2018 thru 10.16.2018

Name of plugin changed to "Medeek Truss".
Updated the licensing system to include a 30 day limit of the trial version.
Updates to the HTML pages of the global settings.
Updated the "Edit Truss Assembly" menu so that it properly loads default values when advanced options are expanded.
Added a user definable name to truss assemblies that will be utilized in the future options and upgrades.

Version 2.2.1 - 10.05.2018

The trim tool now allows for multiple trim operations once a trimming plane is selected.
Pressing the ESC key will reinitialize the trim tool during multiple trim operations, space bar will terminate.
The trim tool will now trim components as well as groups.

Version 2.2.0 - 06.19.2018 thru 09.25.2018

Sub-groups within roof and floor truss assemblies can be made persistent by naming these groups or component instances to (custom1, custom2, custom3, etc...), also all other user defined geometry (ie. faces, text, lines and dimensions) are also retained when the assemblies are regenerated by the plugin.
Fixed a bug so that structural outlookers can be enabled without utilizing a gable end truss.

Version 2.1.9 - 05.27.2018

Replaced the 64 bit SketchUp check in the installation module to fix an incompatibility issue with SketchUp 2014.
Added additional wall cladding materials in the sheathing tab of the global settings.
Fixed a bug in the top level assembly method of the roof truss module.

Version 2.1.8 - 03.18.2018

Enabled the "Edit Floor Assembly" function for all I-Joist floors (imperial and metric units): TJI, BCI, LPI, Red-I, PKI.

Version 2.1.7 - 03.06.2018

Enabled the "Edit Truss Assembly" function for all common roof trusses (imperial and metric units).
Added ceiling gypsum and ceiling battens to cathedral trusses.

Version 2.1.6 - 03.02.2018

Added Soffit Cut within Advanced Options for Hip Rafter Roofs.
Added Soffit Cut within Advanced Options for all Shed type Rafter Roofs.
Added gutters for all Shed type Rafter Roofs.

Version 2.1.5 - 02.16.2018

Added floor sheathing and attic gypsum for gambrel attic trusses.
Added roof cladding, sheathing and ridge cap for gambrel attic trusses.
Created a separate HTML menu for advanced options of gambrel attic trusses.
Enabled gable end trusses for gambrel attic trusses.
Enabled hurricane ties for gambrel attic trusses.
Added a crow's beak option for gambrel attic trusses.
Added thumbnails for wall and roof materials in the sheathing tab of the global settings.
Added a color picker and the ability to change the color of the interior sheathing (gypsum) within the sheathing tab of the global settings.

Version 2.1.4 - 01.20.2018

Completed energy/raised heels for attic trusses (2 variants: wedge and slider).
Added floor sheathing and attic gypsum for attic trusses.
Created a separate HTML menu for advanced options of attic trusses.
Enabled gable end trusses for attic trusses.
Added a graphical user interface for (metric) advanced options of truss roofs.

Version 2.1.3 - 12.31.2017

Enabled hurricane ties for fink and howe common trusses.

Version 2.1.2 - 12.18.2017

Enabled vertical and angled heel blocking within the advanced options for truss roofs.

Version 2.1.1 - 12.04.2017

Enabled a graphical user interface for advanced options of truss roofs.

Version 2.1.0 - 11.28.2017

Added Northeast hip truss set.
Enabled advanced options for northeast hip sets.
Added energy/raised heels for northeast hip set (3 variants: wedge, slider and vertical w/ strut).
Added the option for open vs. closed end jacks.
Added the option for a drop in purlin frame.
Enabled a graphical user interface for Truss Set selection.

Version 2.0.9 - 11.25.2017

Structural outlookers (vert. & horz.) enabled under advanced roof options for Parallel Chord truss type.
Metal plate connectors now enabled for all parallel chord trusses.

Version 2.0.8 - 11.18.2017

Added language support for the following languages: French, Spanish, German, Russian, Swedish, Japanese, Korean, Chinese.
Added a language option in to the "General Tab" of the Global Settings.
Fixed a bug in the gutter module for metric templates.

Version 2.0.7 - 11.16.2017

Added license tab to the global settings.
Minor updates to the licensing system.

Version 2.0.6 - 11.10.2017

Added gutters and downspouts for rafter and truss gable roofs.
Added gutters and downspouts for dutch gable rafter roofs.

Version 2.0.5 - 11.05.2017

Added gutters and downspouts for rafter and truss hip roofs.
Gutter menu added to the global settings.
Custom roof layer added for gutters in the layer menu within the global settings.

Version 2.0.4 - 10.21.2017

Added Parallel Chord (vaulted) truss type, configurations: (2/2, 4/4, 6/6, 8/8).

Version 2.0.3 - 10.13.2017

Added the option to provide a face mount hanger for inset floor joists with ledgers.
Added the option to provide a top flange hanger for inset floor joists without ledgers.
Added an option in the global settings to enable or disable manufacturer's logos.
Face mount hangers added for solid sawn floor joists.
Added Red Built Red-I™ I-joists: 45, 65, 90, 90H, 90HS.
Added PinkWood SAFEjoists™ I-joists: PKI 10, PKI 20, PKI 23, PKI 35Plus, PKI 40, PKI 50.

Version 2.0.2 - 10.07.2017

Added the option to inset floor joists with ledger.
Added the option to inset floor joists without ledger.
I-Joists are branded with respective manufacturer's logo.

Version 2.0.1 - 10.04.2017

Added (FULL) roof return option within the advanced options menu for common, scissor and vaulted trusses.
Added ceiling joist option for Hip Rafter Roofs.

Version 2.0.0 - 09.30.2017

Added a hip & ridge option for dutch gable rafter roofs.
Enabled roof cladding for shed and shed w/ ledger rafter roofs.

Version 1.9.9 - 09.12.2017

Added a hip & ridge option for gable rafter roofs.
Fixed some miscellaneous bugs with rafter roof modules.

Version 1.9.8 - 09.04.2017

Added queen post and howe timber trusses with bolts and metal plates.
Enabled option for F436 vs. F844 flat washers for timber trusses (in the materials tab within the global settings).
Updated license registration system.

Version 1.9.7 - 08.26.2017

Added king post timber trusses with bolts and metal plates.

Version 1.9.6 - 07.29.2017

Added a hip & ridge option for all hip type roofs.
Added a hip & ridge option for all gable truss roofs.

Version 1.9.5 - 07.11.2017

Added energy/raised heels for quad fink truss (3 variant: wedge, slider and vertical w/ strut).
Metal plate connectors now enabled for quad fink trusses.

Version 1.9.4 - 07.08.2017

Added energy/raised heels for triple howe truss (3 variant: wedge, slider and vertical w/ strut).
Metal plate connectors now enabled for triple howe trusses.

Version 1.9.3 - 06.25.2017

Added Terminal hip set trusses.
Enabled advanced options for terminal hip sets.
Added energy/raised heels for terminal hip set (3 variants: wedge, slider and vertical w/ strut).
Added the option for open vs. closed end jack and single and double ply girders.

Version 1.9.2 - 06.24.2017

Added Stepdown hip set trusses.
Enabled advanced options for stepdown hip sets.
Added energy/raised heels for stepdown hip set (3 variants: wedge, slider and vertical w/ strut).
Added the option for open vs. closed end jacks.

Version 1.9.1 - 06.09.2017

Added plywood gusset plates for common fink trusses.
Enabled a "WOOD" plate type option in the global settings.
Added plywood gusset plates for raised heel common fink trusses.

Version 1.9.0 - 05.27.2017

Added flat truss type, configurations: flat, monopitch, pitched, double pitched.
Metric input enabled for flat truss types.
Added gable end trusses for flat truss types.
Enabled six end details for all flat truss types: None, Overhang, Cantilever, Mansard, Parapet, Mansard w/ Parapet.
Enabled top chord bearing for the double pitched flat truss configuration.
Enabled mod warren webs for the double pitched flat truss configuration.

Version 1.8.9 - 05.01.2017

Added energy/raised heels for triple fink truss (3 variant: wedge, slider and vertical w/ strut).
Metal plate connectors now enabled for triple fink trusses.

Version 1.8.8 - 04.28.2017

Added energy/raised heels for mod fan truss (3 variant: wedge, slider and vertical w/ strut).
Metal plate connectors now enabled for mod fan trusses.

Version 1.8.7 - 03.26.2017

Added energy/raised heels for double howe truss (3 variant: wedge, slider and vertical w/ strut).
Metal plate connectors now enabled for double howe trusses.

Version 1.8.6 - 02.25.2017

Added 2x sawn lumber and LSL headers for Gable Dormers.
Enabled interior wall sheathing (Gypsum Wall Board) for Gable Dormers.
Enabled ceiling sheathing (Gypsum Wall Board) and ceiling battens for common trusses.

Version 1.8.5 - 02.18.2017

Enabled roof cladding for dutch gable and TJI rafter roofs.
Added TJI rafter roofs with dual glulam beams.
Added Soffit Cut within Advanced Options for TJI Roof w/ GLB.

Version 1.8.4 - 02.14.2017

Enabled roof cladding for gable and hip rafter roofs.
Roof slope can be toggled between Pitch or Degrees (input) for gable and hip rafter roofs in the global settings.

Version 1.8.3 - 02.12.2017

Enabled metal plate connectors, materials and custom layers for Fan trusses.
Added energy/raised heels for Fan truss (3 variants: wedge, slider and vertical w/ strut).
Roof slope can be toggled between Pitch or Degrees (input) for common trusses in the global settings.

Version 1.8.2 - 02.05.2017

Enabled metal plate connectors, materials and custom layers for Mod Queen trusses.
Added energy/raised heels for Mod Queen truss (3 variants: wedge, slider and vertical w/ strut).
Added a "Front Only" option for gable end trusses.

Version 1.8.1 - 01.29.2017

Enabled gable wall cladding for common trusses.
Added four "HARDIPLANK Cedarmill" siding colors into the wall cladding material library.
Enabled sheathing and cladding for valley truss sets.

Version 1.8.0 - 01.22.2017

Enabled roof cladding for common trusses.
Added nine "IKO Cambridge" architectural shingle colors into the roof cladding material library.
Added "plywood" material for roof and floor sheathing.
Added a "Sheathing" tab into the global settings.
Added entries in the "General" tab of the global settings to toggle default settings for gable end trusses and advanced options.

Version 1.7.9 - 01.15.2017

Enabled metal plate connectors, materials and custom layers for king post, howe, double fink and queen post trusses.
Added energy/raised heels for queen post truss (3 variants: wedge, slider and vertical w/ strut).
Added energy/raised heels for howe truss (3 variants: wedge, slider and vertical w/ strut).
Added energy/raised heels for double fink truss (1 variant: vertical w/ strut).
Metal plate connectors now enabled for king post, queen post, fink, howe, and double fink raised heel/energy trusses.

Version 1.7.8 - 01.02.2017

Enabled materials and custom layers for gable dormers.
Added advanced options for gable dormers, enabled exterior wall sheathing option.
Fixed bug in valley truss set module involving connector plates.

Version 1.7.7 - 12.31.2016

Enabled materials and custom layers for gable, hip, shed, TJI and dutch gable rafter roofs.

Version 1.7.6 - 12.26.2016

Enabled metal plate connectors for monopitch trusses.
Enabled materials and custom layers for monopitch trusses.

Version 1.7.5 - 12.24.2016

Enabled metal plate connectors for valley truss sets.
Enabled materials and custom layers for valley truss sets.

Version 1.7.4 - 12.20.2016

Enabled metal plate connectors for gambrel attic trusses.

Version 1.7.3 - 12.17.2016

Added a "Materials" tab within the global settings; Auto material assigment (colors and textures) is now an option.
Enabled materials and custom layers for floor trusses and joists.
Enabled materials for common trusses: metal plate connectors, lumber, and OSB.
Enabled metal plate connectors for floor trusses.

Version 1.7.2 - 12.16.2016

Enabled custom layers for roof returns, battens and counter battens.
License renewal enabled in Medeek Account Manager.

Version 1.7.1 - 12.10.2016

Added truss connector plates within the global settings, plate thickness can be specified.
Added a "roof_mpc" layer for roof truss plates, connector plates can be assigned to a specific layer.
Enabled metal plate connectors for the common fink truss.
Enabled metal plate connectors for the common gable truss.
Enabled metal plate connectors for the 4/4 and 6/4 scissor trusses.

Version 1.7.0 - 12.04.2016

Added a "Layers" tab within the global settings; roof, wall and floor components can be assigned to specific layers.
Enabled custom layers for the common fink truss.

Version 1.6.9 - 09.14.2016

Added some enhancements and wireframe (temporary) graphics to the valley set function.
Fixed bug in the trim function.
Fixed bug in the roof battens option.

Version 1.6.8 - 08.20.2016

Added the Medeek Tools toolbar with Trim and Extend icons.
Added the trim function for (solid) groups and components.

Version 1.6.7 - 07.21.2016

Added a counter battens option within the battens menu for common, scissor and vaulted trusses.
Battens (at peak) can be offset from peak.
Peak-to-Eave spacing option available when "battens at peak" option is selected.

Version 1.6.6 - 07.15.2016

Added roof battens option within the advanced options menu for common, scissor and vaulted trusses.
Battens can be offset from the fascia board.
Battens at peak option enabled.
Battens are positioned above the roof sheathing when sheathing option is applied.

Version 1.6.5 - 07.07.2016

Added energy/raised heels for polynesian truss type (1 variant: vertical w/ strut).
Fixed HTML truss selector menu so that window size no longer truncates truss images.

Version 1.6.4 - 06.27.2016

Added roof return option within the advanced options menu for common, scissor and vaulted trusses, configurations: (HIP).
Roof return pitch can be set independent of main roof pitch.

Version 1.6.3 - 06.19.2016

Added Gable Dormers to the Minor Roof Sub-Menu (dormer walls only).

Version 1.6.2 - 06.14.2016

Added Symmetric Cathedral truss type, configurations: (AUTO).
Metric input enabled for symmetric cathedral truss type.
Added gable end trusses for symmetric cathedral truss type.
Structural outlookers (vert. & horz.) enabled under advanced roof options for Symmetric Cathedral truss type.

Version 1.6.1 - 06.11.2016

Added Coffer truss type, configurations: (AUTO).
Metric input enabled for coffer truss type.
Added gable end trusses for coffer truss type.
Structural outlookers (vert. & horz.) enabled under advanced roof options for Coffer truss type.
Building parameter menu (2nd) and advanced options menu for trusses now default to last picked options of the session for that sub-menu item.

Version 1.6.0 - 06.08.2016

Corrected a bug with raised heel fink trusses and structural outlookers.
Metric GUI for gambrel attic truss type now shows metric and imperial units in preview pane.
Added energy/raised heels for king post truss (3 variants: wedge, slider and vertical w/ strut).

Version 1.5.9 - 05.29.2016

Increased top chord pitch limit from 12/12 to 18/12 for the following Scissor truss types, configurations: (2/2, 4/4).
Heel web logic revised to accommodate steeper pitches for bottom and top chords of scissor trusses.
Increased top chord pitch limit from 12/12 to 18/12 for valley truss sets.

Version 1.5.8 - 05.22.2016

Added metric input for Gambrel Attic truss type.
Added a graphical user interface (GUI) for metric gambrel attic geometry input.

Version 1.5.7 - 05.15.2016

Added Scissor truss type, configurations: (4/2, 6/4).
Structural outlookers (vert. & horz.) enabled under advanced roof options for Scissor (4/2, 6/4) truss types.

Version 1.5.6 - 05.11.2016

The plugin now automatically checks for updates.
Option added in Global Settings to adjust frequency of "check for updates" or to disable this feature entirely.

Version 1.5.5 - 04.29.2016

Added Gambrel Attic truss type, configurations: (AUTO w/ piggyback trusses).
Added a graphical user interface (GUI) for gambrel attic geometry input.

Version 1.5.4 - 04.21.2016

Added a graphical user interface (GUI) for the selection of the truss type in the "Draw Roof Truss" sub-menu.
GUI can be toggled with previous drop down menu within global settings.

Version 1.5.3 - 04.20.2016

Added Mono Cathedral truss type, configurations: (2/2, 4/4).
Metric input enabled for mono cathedral truss type.
Added gable end trusses for mono cathedral truss type.
Structural outlookers (vert. & horz.) enabled under advanced roof options for Mono Cathedral (2/2, 4/4) truss types.
Added Mono Scissor truss type, configuration: (4/4).

Version 1.5.2 - 04.18.2016

Added energy/raised heels for small span attic trusses (less than 24 ft.), 1 variant: vertical w/ strut.
Added some additional logic to improve the triangulation of the upper attic of attic trusses.

Version 1.5.1 - 04.16.2016

Added Dutch Gable Rafter Roof (all advanced options enabled).
Added wireframe (temporary) graphics to the roof positioning tool for rafter roofs.

Version 1.5.0 - 04.11.2016

Added Mono Scissor truss type, configurations: (2/2, 3/3).
Metric input enabled for mono scissor truss type.
Added gable end trusses for mono scissor truss type.
Structural outlookers (vert. & horz.) enabled under advanced roof options for Mono Scissor (2/2, 3/3) truss types.

Version 1.4.9 - 04.04.2016

Added Tray truss type, configurations: (AUTO).
Metric input enabled for tray truss type.
Added gable end trusses for tray truss type.

Version 1.4.8 - 04.01.2016

Added Mod Fan common truss type.
Structural outlookers (vert. & horz.) enabled under advanced roof options for Common (Mod Fan) truss type.

Version 1.4.7 - 03.28.2016

Added Cathedral truss type, configurations: (4/X, 6/X).
Metric input enabled for cathedral truss type.
Added gable end trusses for cathedral truss type.

Version 1.4.6 - 03.26.2016

Added Cambered truss type, configurations: (6/X).
Metric input enabled for cambered truss type.
Added gable end trusses for cambered truss type.

Version 1.4.5 - 03.24.2016

Structural outlookers (vert. & horz.) enabled under advanced roof options for Scissor (4/4) truss type.

Version 1.4.4 - 03.21.2016

Added Polynesian truss type, configurations: (4/4).
Metric input enabled for polynesian truss type.
Added gable end trusses for polynesian truss type.

Version 1.4.3 - 03.20.2016

Added Scissor truss type, configuration: (6/6).
Added energy/raised heels for scissor trusses (2 variants: wedge and vertical w/ strut).
Addressed some minor usability issues with the scissor truss menu and options.

Version 1.4.2 - 03.19.2016

Added energy/raised heels for attic trusses (1 variant: vertical w/ strut).
Addressed some minor usability issues with the attic truss menu and options.

Version 1.4.1 - 03.16.2016

Added Soffit Cut within Advanced Options for Gable Roof and Gable Roof w/ GLB.

Version 1.4.0 - 03.15.2016

Added LP Solidstart^® I-joists: 450, 530, 18, 36, 56.
Rim joist option enabled for LPI floor joists.

Version 1.3.9 - 03.14.2016

Out-to-out span of trusses in the trial version are now limited to a range of: 16 ft. (5m) - 32 ft. (9m).

Version 1.3.8 - 03.10.2016

Added wireframe (temporary) graphics to the truss positioning tool.
Added Boise Cascade BCI^® I-joists: 4500, 5000, 6000, 6500, 60, 90.
Rim joist option enabled for BCI floor joists.
Removed drop down lists for all overhang lengths (truss & rafter roofs). Overhangs are now users inserted values.

Version 1.3.7 - 03.06.2016

Added Soffit Cut within Advanced Options for common fink truss type.

Version 1.3.6 - 03.06.2016

Added Double Howe and Triple Howe common truss types.
Structural outlookers (vert. & horz.) enabled under advanced roof options for Common (Double & Triple Howe) truss types.

Version 1.3.5 - 03.04.2016

Added Bow Barrel truss type, configurations: (8/8).
Metric input enabled for bow barrel truss type.
Corrected a bug with the webs of the bowstring truss type.

Version 1.3.4 - 03.02.2016

Corrected a bug in the metric unit template module.

Version 1.3.3 - 02.28.2016

Added Bowstring truss type, configurations: (6/6, 8/8).
Metric input enabled for bowstring truss type.

Version 1.3.2 - 02.23.2016

Added Dualpitch truss type, configurations: (2/2-3/3).
Metric input enabled for dualpitch truss type.
Advanced options enabled for dualpitch truss type.

Version 1.3.1 - 02.17.2016

New submenu item and toolbar icon added for global settings.
Addressed a number of bugs in the rafter roof sub-menu for metric units.

Version 1.3.1 - 02.15.2016

Added Triple Fink and Quad Fink common truss types.
Structural outlookers (vert. & horz.) enabled under advanced roof options for Common (Triple & Quad Fink) truss types.

Version 1.3.0 - 02.14.2016

Added Tail Bearing truss type, configurations: (Fink).
Metric input enabled for tail bearing truss type.
Advanced options enabled for tail bearing truss type.

Version 1.2.9 - 02.12.2016

Added Shed Rafter Roof (all advanced options enabled).
Added ceiling joist option for Shed Rafter Roofs.
Initial menu now defaults to last picked option of session for that sub-menu item.

Version 1.2.8 - 02.08.2016

Official documentation of plugin: Medeek Truss Plugin Manual.
Plugin is now listed in the SketchUcation PluginStore.

Version 1.2.8 - 02.02.2015

Added Shed Rafter Roof with Ledger (all advanced options enabled).
Added ceiling joist option for Shed Rafter Roof with Ledger.
New submenu item and toolbar icon added for secondary (minor) roofs.

Version 1.2.7 - 01.26.2016

Added advanced roof options for hip rafter roof (sheathing, fascia).

Version 1.2.6 - 01.19.2016

Added Solid Sawn Floor Joists (metric and imperial)
Sill plate and Sheathing options (advanced) enabled for TJI and Solid Sawn floor joists.

Version 1.2.6 - 01.18.2016

Sill plate option (advanced) enabled for top and bottom bearing floor trusses.

Version 1.2.5 - 01.10.2016

Plugin integrated with the Medeek Beam Calculator.
Engineering of North American glulam beam sizes enabled (Western, Southern Pine).

Version 1.2.4 - 01.08.2016

Plugin integrated with the Medeek Truss Designer.
Engineering of common fink truss enabled.
New submenu item and toolbar icon added for engineering.

Version 1.2.3 - 01.01.2016

PayPal purchase option enabled in Medeek Account Manager.

Version 1.2.3 - 12.29.2015

Added Hip Rafter Roof.

Version 1.2.2 - 12.23.2015

Structural outlookers notched around TJI top flange when oriented vertically.

Version 1.2.2 - 12.21.2015

Added TJI Rafter Roof with Glulam Beam (all advanced options enabled).
Added dropped beam option for TJI Rafter Roof with Glulam Beam: Bevelled plate.

Version 1.2.1 - 12.16.2015

Added gable end trusses (ladders) and ribbon boards to the floor truss type (Warren - System 42).
Sheathing option enabled under advanced floor options for floor trusses.

Version 1.2.0 - 12.13.2015

Added ceiling joist option for Gable Rafter Roof.

Version 1.1.9 - 12.11.2015

Added Glulam Beam Standard Sizes (metric) for: United Kingdom, South Africa, Australia (and New Zealand).
Added dropped beam options for Gable Rafter Roof with Glulam Beam: Notched rafter and Bevelled plate.

Version 1.1.9 - 12.10.2015

Added Gable Rafter Roof with Glulam Beam (all advanced options enabled).
Added Glulam Beam Standard Sizes (Imperial) for the United States - AWC 2012 NDS Supplement Tables 1C,1D.

Version 1.1.8 - 12.08.2015

Structural Outlookers enabled for gable rafter roofs (vertical & horizontal).

Version 1.1.8 - 12.07.2015

Added Gable Rafter Roof.
Advanced options enabled for gable rafter roofs (sub-fascia, outlookers, sheathing, and rakeboards).
New submenu item and toolbar icon added for rafter roof type.
Plugin divided into multiple files for ease of management.

Version 1.1.7 - 11.28.2015

Valley sets enabled for perpendicular roof lines.

Version 1.1.6 - 11.26.2015

Added Fan and Mod Queen common truss types.
Structural outlookers (vert. & horz.) enabled under advanced roof options for Common (Fan & Mod Queen) truss types.

Version 1.1.5 - 11.25.2015

Added Double Fink common truss type.
Structural outlookers (vert. & horz.) enabled under advanced roof options for Common (Double Fink) truss type.

Version 1.1.4 - 11.25.2015

Structural outlookers (vert. & horz.) enabled under advanced roof options for Common (Fink) truss type.
Structural outlookers (vert. & horz.) enabled under advanced roof options for Common (Fink) truss type with raised heel (vertical w/ strut).

Version 1.1.3 - 11.21.2015

Outlookers enabled under advanced roof options for Common, Scissor, Monopitch and Attic truss types.
Gable end trusses enabled for (2/2, 4/4) scissor truss types.

Version 1.1.2 - 11.16.2015

Metric input enabled for monopitch truss types.

Version 1.1.1 - 11.14.2015

Gable end trusses enabled for all monopitch truss types.
Added energy/raised heels for monopitch trusses (3 variants: wedge, slider and vertical w/ strut).
Added advanced roof options for monopitch truss type (sheathing, rake, fascia).

Version 1.1.0 - 11.10.2015

Gable end trusses enabled for the Fink truss type and all raised heel variants.
Gable end trusses enabled for the Queen Post and Howe truss types.

Version 1.1.0 - 11.08.2015

Added advanced roof options for Common, Scissor and Attic truss types.
Sheathing option enabled under advanced roof options.
Rake Board option enabled under advanced roof options.
Fascia (Flush, Dropped, Beveled) option enabled under advanced roof options.

Version 1.0.9 - 11.05.2015

Added separate toolbar icons for floor trusses and joists.
Created separate submenu items under the Medeek Truss Plugin Extension for roof and floor trusses.

Version 1.0.8 - 11.04.2015

Added Weyerhauser TJI^® I-joists: 110, 210, 230, 360, 560, 560D.
Rim joist option enabled for TJI floor joists.

Version 1.0.7 - 11.03.2015

Trusses can now be positioned and sized via three mouse clicks, with the option for manual overide in the dialog windows.
The number of trusses is now based on the spacing and building length.
Floor trusses with top chord bearing now are positioned properly.
Gable end trusses enabled for the King Post truss type.

Version 1.0.6 - 10.25.2015

Added floor truss type, Modified Warren - System 42.
Metric input enabled for floor truss types.
Top and bottom bearing option enabled for left and/or right end of floor trusses.
Ribbon cut option (top) enabled for left and/or right end of floor trusses.

Version 1.0.5 - 10.24.2015

Added Scissor truss type, configurations: (2/2), (4/4).
Metric input enabled for scissor truss types.

Version 1.0.4 - 10.21.2015

Added a toolbar icon for the plugin.
Metric input enabled for common truss types.
Plugin is now listed on SketchUp Extension Warehouse.

Version 1.0.4 - 10.20.2015

Added Howe truss type.
Added Monopitch truss type, configurations: (2/2), (3/3).
All global variables removed in order to comply with requirements of SketchUp Extension Warehouse and to ensure compatibility with other extensions.

Version 1.0.3 - 10.19.2015

Added Attic truss type.
Autosizing of attic width and height enabled for attic trusses.
Trusses are now created as components with each individual member of the truss a group. Arrays of trusses are multiple instances of the same component.

Version 1.0.2 - 10.16.2015

Added energy/raised heels for fink truss (3 variants: wedge, slider and vertical w/ strut).
Added King Post and Queen Post truss types.
Left and right overhangs can now be set independently.

Version 1.0.0 - 10.07.2015

Created Medeek Truss Plugin, utilizing SketchUp's Ruby API.
Added the fink truss geometry algorithm with the ability to create a single truss or an array of trusses.

For a more in depth look at the development of the plugin and related discussions please visit the Medeek Forum.

If you have any questions about the Medeek Truss Plugin or its development please contact us.